Protecting and repairing your basement is an extremely important part of keeping your home waterproof. There are a lot of threats to your home, but none are as prevalent and dangerous than a basement crack. Cracks in your basement walls or floor allow water into your basement. This water causes flooding, which damages your basement, your foundation, and anything you have stored in your basement. If you want to fully protect your homes, you need to repair and protect your basement. Failing to protect your basement is a mistake you can’t afford to make.
Many homes around the world enjoy the benefits and stability of concrete block foundations. Concrete block is a strong, durable building material, which is why it’s used in so many homes. While concrete block foundations are sturdy, they are not without their drawbacks. If you’re looking for a strong foundation material, you’ll be hard-pressed to find one better than concrete block. However, these same block foundations have certain problems associated with them. Concrete block foundations are subject to two major concerns: water intrusion and cracking. You can have the nicest house on your street, but a cracked, leaking basement can do immense damage in a short period of time.
Whether it’s a complete disaster or just a few noticeable cracks, concrete repair is not something to take lightly. Although it’s a strong, durable, and long-lasting material, concrete is not indestructible. In some cases, concrete needs repaired to make it look good again. In those cases, you need an effective and long-lasting repair. If your concrete driveway, walkway, patio, or floor needs repaired, you need a material that will not only repair cracks or imperfections, but also protect your concrete from future damage.
For more information about concrete repair and waterproofing, visit SANI-TRED
Nearly all driveways will develop cracks at some time or other. The causes can be numerous. One is tree roots growing beneath
the pad and another is the freeze-thaw cycle which can expand and contract concrete 9%. Instead of having to break up and pour a brand new slab, why not just repair the cracks with a little Sani-Tred.
Preparation to remove all the mold, mildew, and ground in dirt is the single most important factor in preparing concrete. To prepare concrete acid etching and pressure watching is the best option. This is accomplished by mixing “Muratic Acid” and water. Muratic Acid is commonly found at most larger hardware stores, paint supply stores, lumber companies, swimming pool supply stores, Wal-Mart, Kmart, etc.
How To Acid Etch Concrete
Muratic Acid is typically packaged at a 30% dilution; you want to dilute it down to a 10% by diluting 3 parts water to one part acid. You’ll need a gallon of diluted acid for every 200 square feet. Pour acid carefully in to water to avoid splashing, and use appropriate safety equipment.
Thoroughly wet concrete before applying acid. Apply acid dilution evenly using a garden watering can. After applying acid will begin to bubble, use a push broom to work it in, and then let sit for 10 minutes. Afterwards use a pressure washer to clean the concrete off. Then neutralize by applying a solution of 1 cup baking soda to 1 gallon of water then pressure wash again. For more detailed step by step instructions on acid etching concrete watch the video below or visit http://www.wikihow.com/Acid-Etch-Concrete.
Crack Repair and Resurfacing Concrete Driveways
Take extra pains to clean out all the cracks and crevices you may see, no matter how small or thin. You want your concrete patching to have a good surface to adhere to.
Once the concrete is completely dry. Prime the concrete with 1 coat of PermaFlex (240 sq ft per gal) using a roller or squeegee. This coat of PermaFlex will act as a binder within the substrate. PermaFlex can be thinned using either Xylene (in states where allowed) or Acetone to encourage even more rapid and deeper absorption/penetration.
Patch and profile any joints, seams, cracks, holes and rough areas using LRB/TAV mixture. 2-parts LRB is mixed with 1-part TAV to create the thickest mixture possible (similar in viscosity as silicone caulk). Wall/floor junctions require a 1” diameter caulk bead of LRB/TAV mixture and most other cracks & joints use a 3/4” diameter caulk bead.
After applying basecoat and patching cracks with LRB apply a topcoat of PermaFlex® (240 sq ft per gal). If you are looking for a decorative surface you can achieve the look of granite with our Graniflex system http://theconcreteprotector.com/graniflex-decorative-coating/.
Your repaired driveway should be able to handle foot traffic within 6 hours of adding the texture to it. Give it about 24 hours before driving your car onto it. This does a really good job of patching without having to bust up everything and deal with the mess and also suffer the costs of putting in a whole new driveway.
The Sani-Tred Solution
Looking for a garage floor or driveway coating that will keep your concrete from ever cracking again? Sounds to good to be true? Sani-Tred permanently bonds with concrete at a molecular level, and provides 590% elongation. It’s the only product of it’s kind with a lifetime guarantee. To learn more visit http://sanitred.com/garage-floor-coating-waterproof/ or call 1-866-784-3308