A cracked or pitted concrete ramp can usually be repaired and resurfaced instead of torn out. You clean and etch the concrete, prime it, fill the cracks and pits with a flexible rubber patch, rebuild broken edges, and finish with a textured topcoat for grip. On a wheelchair ramp the finished surface also has to be smooth enough to roll over and slip resistant when wet, so the repair has to be level and the texture has to be even. This guide covers how to repair a concrete ramp step by step, the accessibility rules that matter for a repair, and a clinic ramp we helped fix.
Why concrete ramps break down
Ramps take more abuse than most concrete. They are sloped, so water runs down them instead of draining off, and they are usually outdoors with no roof. Common problems:
- Freeze-thaw damage. Water soaks into the surface, freezes, and expands. Over a few winters the top flakes off (scaling) and pits open up.
- Deicing salt. Salt spread for safety speeds up scaling and pitting.
- Cracks from shrinkage, settling soil, and the joint where the ramp meets the sidewalk or building.
- Broken edges and curbs. Edge protection and the sides of the ramp chip and spall.
- Worn, slick surfaces. A broom finish wears smooth over time, and smooth concrete is slippery when wet.
For a wheelchair user, a crack or pit that a walker steps over can catch a front caster. A lip of a quarter inch is enough to stop a chair or tip it.
Repair or replace?
Repair works when the ramp is still solid and in the right place. Replace it, or call an engineer, if:
- sections have settled so the ramp has steps or dips in it,
- the slope is too steep for the ramp to meet accessibility rules (resurfacing does not change slope),
- large chunks are loose or the ramp is hollow underneath, or
- rebar is exposed and rusting through the surface.
Cracks, pitting, scaling, small broken edges, and a slick surface are all good candidates for repair and resurfacing.
Accessibility rules that affect a ramp repair
If the ramp serves a business, clinic, church, or other public building, it falls under the 2010 ADA Standards for Accessible Design. A repair should not make the ramp less compliant. A few of the rules that apply to the surface:
- Running slope of no more than 1:12 (1 inch of rise per 12 inches of run).
- Cross slope of no more than 1:48.
- Clear width of at least 36 inches between handrails.
- Surfaces that are firm, stable, and slip resistant.
- Changes in level of up to 1/4 inch can be vertical. Between 1/4 inch and 1/2 inch they must be beveled. Anything taller has to be treated as a ramp.
- Openings in the walking surface, such as cracks and joints, should not let a 1/2-inch sphere pass.
That last pair matters most for repair work. Filling cracks flush and grinding down raised edges brings a damaged surface back within these limits. Residential ramps often are not covered by the ADA, but the same numbers are a good target for a safe ramp at home. Check with your local building department for the codes that apply to your project.
What you need
- Pressure washer, degreaser, and a stiff broom
- Muriatic acid, a plastic watering can, and baking soda for etching, or a grinder
- PermaFlex for the primer and topcoat (240 sq ft per gallon per coat)
- LRB (Liquid Rubber Base) and TAV (Thickening Activator) for cracks and pits
- Silica sand, plywood, and plastic sheeting if you need to rebuild an edge
- Rubber texture granules, masking tape, rollers, and a putty knife or trowel
How to repair and resurface a concrete ramp
1. Grind high spots and clean
Grind down any raised edges at cracks or joints so the surface is close to level. Remove old paint and sealer. Pressure wash the whole ramp with degreaser and let it dry.
2. Etch
Acid etch the concrete so the primer can soak in. Dilute muriatic acid to a 10 percent solution, broom it in until the foaming stops, rinse, neutralize with baking soda and water, and rinse again. On a ramp, work from the top down so the acid does not pool at the bottom. Follow our acid etching guide. Let the ramp dry completely.
3. Prime
Roll one coat of PermaFlex over the ramp, landings, and the walkway approach at 240 sq ft per gallon. Work it into the cracks and pits. PermaFlex soaks into the concrete and binds weak, flaking surface material together.
4. Fill cracks and pits
Mix 2 parts LRB with 1 part TAV into a thick, caulk-like rubber. Pipe it into cracks and the joint where the ramp meets the sidewalk or building with a heavy-duty zip-loc bag, then strike it off flush with a putty knife. The goal is a flat surface with no lips or dips. For shallow pits and scaled areas, use a runnier mix (less TAV) or straight LRB, which self-levels. The patch cures to solid rubber in about 4 hours and stays flexible, so it does not pop out when the concrete moves. The crack filling calculator helps estimate material.
5. Rebuild broken edges
For chipped ramp edges and curbs, build a form from plywood wrapped in plastic sheeting (SANI-TRED does not stick to it). Mix 1 part LRB with up to 3 parts silica sand and pack it into the form. Pull the form after the mix cures and touch up any gaps with LRB. This is the same method we use on step nosings. See concrete step repair and resurfacing for photos and details.
6. Texture for traction
A ramp needs grip in the rain. Apply a coat of PermaFlex and broadcast rubber texture granules evenly into it while it is wet. Mask off areas you want to keep smooth, such as curb faces. When the PermaFlex cures, sweep off the loose granules. Then lock the texture in with a coat of LRB at about 60 sq ft per gallon. Keep the texture even across the full width so wheels roll smoothly. See slip resistant floor coverings for texture options.
7. Topcoat and cure
Finish with a topcoat of PermaFlex at 240 sq ft per gallon over the whole surface. Keep foot and wheel traffic off until it cures. Plan the work for a dry stretch of weather, and set up a temporary route if the ramp is the only accessible entrance.
Ramp repair project: a medical clinic and adult daycare
Justin Eckrote of The Nobel Surface was hired to fix the concrete walkway and wheelchair access ramp at a medical clinic and adult daycare that was about to open. The concrete had numerous cracks and pits. Justin repaired them with SANI-TRED products and built a new wheelchair ramp using the same repair products. The finished ramp gave the facility a smooth, safe entrance for patients and visitors.
Keeping a repaired ramp in good shape
- Shovel snow promptly and use sand for traction where you can. Avoid ammonium nitrate and ammonium sulfate deicers, which attack concrete.
- Keep downspouts from emptying onto the ramp.
- Check joints and edges each spring. LRB bonds to itself new to old, so a worn spot can be patched without stripping the ramp.
- Seal nearby bare concrete walks with a penetrating concrete sealer to slow freeze-thaw damage.
Frequently asked questions
How do you repair a cracked concrete ramp?
Clean and etch the concrete, prime with a penetrating coating, fill the cracks flush with a flexible patch, and topcoat with a textured finish. Grind down any raised edges first.
Can you resurface a concrete wheelchair ramp?
Yes, if the ramp is structurally sound and the slope is correct. Resurfacing covers pitting and scaling and adds traction, but it does not change the slope.
What is the best non-slip surface for a concrete ramp?
A textured coating with an even, fine grit. It should be rough enough to grip shoes and tires when wet and even enough for wheelchairs to roll smoothly.
How big a crack is a problem on a wheelchair ramp?
Under the ADA, openings in a walking surface should not let a 1/2-inch sphere pass, and level changes over 1/4 inch need a bevel. Any crack that catches a caster or a toe should be filled flush.
Can I repair concrete ramp edges myself?
Yes. A plywood form wrapped in plastic and an LRB and sand mix rebuilds chipped edges and corners.
Repair your concrete ramp with SANI-TRED
SANI-TRED is a liquid rubber system that bonds into concrete and cures into a flexible surface with up to 590 percent elongation, so cracks stay filled as the ramp moves with the seasons. It is solvent free, non-flammable, and low VOC, and our techs help DIYers and contractors by phone.
- Read how to repair and resurface concrete steps
- See our concrete driveway repair guide for walkways and slabs
- Order PermaFlex, LRB, TAV, and texture granules from the SANI-TRED shop
- Call 1-866-784-3308 to talk through your ramp with a SANI-TRED tech
Sources: U.S. Department of Justice, 2010 ADA Standards for Accessible Design (sections 302, 303 and 405); Portland Cement Association (PCA), guidance on deicer scaling of concrete.
