How to Reduce Radon by Sealing Your Basement

Radon Mitigation Basement - DIY
Radon Mitigation Basement – DIY
Sealing your basement reduces radon by closing the cracks, joints, and porous concrete that the gas moves through. The EPA’s main method for lowering radon is active sub-slab depressurization, a pipe and fan system that pulls gas from under the floor and vents it outside. Sealing works alongside that system and makes it more effective, and a coating that bonds into the concrete also waterproofs the basement at the same time. This guide covers how radon gets in, how the main mitigation methods compare, and how to seal basement walls and floors step by step.

How radon gets into a basement

Radon is a radioactive gas that forms when uranium in soil and rock breaks down. It moves up through the ground and into any part of the house that touches the soil. A basement is the most common way in, because it has the most concrete in contact with the ground and usually sits at lower air pressure than the soil around it. That pressure difference pulls soil gas in through:

  • cracks in the floor slab and walls
  • the cold joint where the wall meets the floor
  • gaps around pipes, sump pits, and floor drains
  • the open cores of concrete block walls
  • the pores of the concrete itself

Water and damp air come in through the same openings. If your basement has damp spots, efflorescence, or a musty smell, the paths radon uses are already there. Our guide to what causes leaky basements covers the water side.

The EPA recommends fixing any home that tests at 4 pCi/L (picocuries per liter) or higher and suggests considering a fix between 2 and 4 pCi/L. Test before you start and again after the work is done. For health effects and testing details, see radon gas symptoms, causes and health effects.

Radon mitigation methods compared

Active sub-slab depressurization (fan system)

This is the method the EPA recommends most often. A contractor drills through the slab, sets a pipe into the gravel or soil below, and runs it to a fan that vents the gas above the roofline. The fan keeps the soil under the house at lower pressure than the basement, so gas flows out through the pipe instead of up into the house. It works best when air can move easily under the slab. The EPA says these systems can bring most homes below 4 pCi/L, and often to 2 pCi/L or less.

Installed cost commonly runs about $1,000 to $3,000, and the fan adds a yearly electric cost. Prices vary by region and by how the house is built. Use a contractor certified through your state or a national radon proficiency program.

Sealing cracks and openings

Sealing closes the paths radon uses to enter. The EPA treats sealing as a basic part of any mitigation job, because open cracks let basement air leak down into the sub-slab area and make the fan work harder. The EPA does not recommend sealing by itself as the only fix, because ordinary caulk and patching cover only the cracks you can see and can fail as the house moves.

Full-surface sealing with a membrane

A coating that covers the entire floor and wall surface goes further than spot caulking. It closes the pores of the concrete as well as the cracks and joints. This is where SANI-TRED fits. In laboratory testing, SANI-TRED blocked 99 percent of radon from passing through treated concrete. Use it on its own where a fan system is not practical, or together with a fan system for the lowest levels and a dry basement.

Other methods

Contractors also use sub-membrane depressurization in crawlspaces (plastic sheeting sealed over the dirt with a vent pipe under it), drain-tile suction, and block-wall suction. Adding ventilation, such as opening lower-level windows, lowers radon only while the air is moving and raises heating and cooling costs, so it does not work as a permanent fix.

Why “radon paint” usually falls short

People search for “radon paint” hoping one coat of a basement sealer will fix the problem. Most masonry paints and waterproofing paints form a thin film on the surface. They do not bridge cracks, and when moisture pushes from behind they blister and peel, which opens the paths back up. A radon barrier has to stay bonded to the concrete, stretch across cracks, and hold up against water and vapor pressure from the soil side.

SANI-TRED is a liquid rubber that soaks into the concrete, bonds to it, and cures into a seamless rubber membrane. The first coat penetrates and cures inside the surface, which is how it stays attached. The patching compound fills joints and cracks with flexible rubber, and the topcoat seals the whole surface. When applied correctly following the instructions, it will not bubble, crack, peel, or delaminate.

SANI-TRED radon test results

In one customer’s home, the radon level before installation measured 155.3 pCi/L, almost 39 times the EPA action level. Immediately after the SANI-TRED system went on, the main living area tested at 0.2 pCi/L. The utility area tested at 0.9 pCi/L; that customer had left an open earth pit for utility pipes, which let some gas through. Results depend on the house and on sealing every opening, so test before and after your own project. See the DIY radon mitigation coating page for the full test results.

How to seal your basement for radon, step by step

Products needed: PermaFlex, LRB (Liquid Rubber Base), and TAV (Thickening Activator). The basic product line page explains how they work together.

1. Test first

Run a radon test so you have a starting number. Keep a copy of the result.

2. Prepare the surface

The concrete must be clean, dry, and free of old paint, sealers, loose material, and dirt. Old coatings block the rubber from soaking in, so remove them. If the floor is smooth or sealed, see how to acid etch concrete.

3. Prime

Apply one coat of PermaFlex at about 240 square feet per gallon. Concrete block needs two prime coats, because block is much more porous than poured concrete. The prime coat soaks into the surface and cures inside it.

4. Patch and profile

Mix 2 parts LRB with 1 part TAV to make a thick, caulk-like rubber compound. Run a 1-inch diameter bead where the wall meets the floor. Fill most cracks with a 3/4-inch bead. Seal around pipes, the sump pit, and floor drains. Cover or seal any open earth in the basement, because one open spot lets gas bypass the rest of the work. The crack filling calculator tells you how much compound you need.

5. Topcoat

Apply one coat of PermaFlex over the walls and floor at about 240 square feet per gallon. After it cures, you can paint over it or finish the room.

6. Retest

Test again after the coating has cured. If the level is still at or above 4 pCi/L, look for unsealed openings or add a fan system. Retest every couple of years and after any major remodel.

Seal for radon and waterproof at the same time

A fan system lowers radon but does nothing about water. A basement that stays damp can still grow mold and ruin finished walls and flooring. Sealing the concrete with SANI-TRED handles both problems with one system. The products are solvent free, non-flammable, and low VOC, carry a lifetime warranty, and come with detailed instructions and phone support for DIY installs.

Frequently asked questions

Does sealing a basement reduce radon?

Yes. Sealing closes the cracks, joints, and pores that radon moves through. The EPA recommends sealing as part of a mitigation system. A full-surface membrane such as SANI-TRED covers far more of the concrete than spot caulking.

Is there a paint that blocks radon?

Ordinary masonry and waterproofing paints are thin films that crack and peel, so they do little for radon. A bonded rubber membrane that bridges cracks and resists water pressure from the soil side is a better choice.

Can I do radon mitigation myself?

You can seal basement walls and floors yourself with SANI-TRED and phone support. Fan systems involve drilling the slab, venting above the roof, and electrical work, so most states recommend a certified radon contractor for those.

How much does radon mitigation cost?

A fan-based system commonly costs about $1,000 to $3,000 installed, plus a yearly electric cost for the fan. Sealing costs depend on the square footage and the number of cracks. Prices vary by region.

Should I seal my basement if I already have a radon fan?

Sealing helps a fan system work better, because less basement air leaks into the sub-slab area. It also stops water and vapor, which the fan does not.

Sources: U.S. EPA, “A Citizen’s Guide to Radon” and “Consumer’s Guide to Radon Reduction.”

1 thought on “How to Reduce Radon by Sealing Your Basement”

  1. I need to know what I would need to do a 900 SQ FT TO PAINT. I WOULD LUKE TO KNOW WHAT TOOLS I NEED TO GET AN HOW MUCH PRODUCT.

    THANK YOU

Comments are closed.

Shopping Cart